ECE 110/Equipment/Ping Sensor

Introduction

The PING ultrasonic sensor is capable of measuring distances by using ultrasonic signals that it bounces off objects. Based on the time it takes for the signal to go from the transmitter, to the object, and back the the receiver, the sensor can estimate distance travelled and then report half that as the distance away from the object.

Leads

There are two styles of PING sensor - one has three leads and the other has four leads. The CX-Bot has a header in place for the three-pin version so that will be the one used in ECE 110. Information on the four-pin version is also provided below.

For the three-pin version of the PING sensor, going from left to right when looking at the front:

• GND: Ground
• VCC: Supply voltage, typically 5 V
• SIG: Pin to set high to trigger the Ping to send a pulse and to monitor to detect the pulse

For the four-pin version of the PING sensor, going from left to right when looking at the front:

• VCC: Supply voltage, typically 5 V
• TRIG: Pin to set high to trigger the Ping to send a pulse
• ECHO: Pin to read to detect the pulse
• GND: Ground

Sample Code

The following code is adapted from https://docs.arduino.cc/built-in-examples/sensors/Ping; the only change is the the CX-Bot uses pin 50 to communicate with the sensor.

/*
  Ping))) Sensor

  This sketch reads a PING))) ultrasonic rangefinder and returns the distance
  to the closest object in range. To do this, it sends a pulse to the sensor to
  initiate a reading, then listens for a pulse to return. The length of the
  returning pulse is proportional to the distance of the object from the sensor.

  The circuit:
	- +V connection of the PING))) attached to +5V
	- GND connection of the PING))) attached to ground
	- SIG connection of the PING))) attached to digital pin 7

  created 3 Nov 2008
  by David A. Mellis
  modified 30 Aug 2011
  by Tom Igoe

  This example code is in the public domain.

  https://www.arduino.cc/en/Tutorial/BuiltInExamples/Ping
*/

// this constant won't change. It's the pin number of the sensor's output:
const int pingPin = 50;

void setup() {
  // initialize serial communication:
  Serial.begin(9600);
}

void loop() {
  // establish variables for duration of the ping, and the distance result
  // in inches and centimeters:
  long duration, inches, cm;

  // The PING))) is triggered by a HIGH pulse of 2 or more microseconds.
  // Give a short LOW pulse beforehand to ensure a clean HIGH pulse:
  pinMode(pingPin, OUTPUT);
  digitalWrite(pingPin, LOW);
  delayMicroseconds(2);
  digitalWrite(pingPin, HIGH);
  delayMicroseconds(5);
  digitalWrite(pingPin, LOW);

  // The same pin is used to read the signal from the PING))): a HIGH pulse
  // whose duration is the time (in microseconds) from the sending of the ping
  // to the reception of its echo off of an object.
  pinMode(pingPin, INPUT);
  duration = pulseIn(pingPin, HIGH);

  // convert the time into a distance
  inches = microsecondsToInches(duration);
  cm = microsecondsToCentimeters(duration);

  Serial.print(inches);
  Serial.print("in, ");
  Serial.print(cm);
  Serial.print("cm");
  Serial.println();

  delay(100);
}

long microsecondsToInches(long microseconds) {
  // According to Parallax's datasheet for the PING))), there are 73.746
  // microseconds per inch (i.e. sound travels at 1130 feet per second).
  // This gives the distance travelled by the ping, outbound and return,
  // so we divide by 2 to get the distance of the obstacle.
  // See: https://www.parallax.com/package/ping-ultrasonic-distance-sensor-downloads/
  return microseconds / 74 / 2;
}

long microsecondsToCentimeters(long microseconds) {
  // The speed of sound is 340 m/s or 29 microseconds per centimeter.
  // The ping travels out and back, so to find the distance of the object we
  // take half of the distance travelled.
  return microseconds / 29 / 2;
}

References

• Three-pin Data Sheet from Parallax via DigiKey.
• Four-pin Data Sheet from Mouser.